The Fourier Series deals with periodic waves and named after J. Fourier who discovered it.

The knowledge of Fourier Series is essential to understand some very useful concepts in Electrical Engineering.Fourier Series is very useful for circuit analysis, electronics, signal processing etc. . The study of Fourier Series is the backbone of Harmonic analysis. We know that harmonic analysis is used for filter design, noise and signal analysis. etc.. Harmonic analysis is also very important in power system studies. In power network, harmonics are mainly generated by non-linear elements and switching equipment. Although it is a applied mathematics topic but like our previous article here also we will try to minimise the maths and depict in a simpler way.

The Fourier Series deals with periodic waves and named after J. Fourier who discovered it.

Fourier Series

The Fourier series is concerned with periodic waves. The periodic wave may be rectangular, triangular, saw tooth or any other periodic form(single valued). Here I will also call this periodic wave as signal wave.Any periodic signal wave can be represented as a sum of a series of sinusoidal waves of different frequencies and amplitudes.

Otherwise we can also say that a series of sinusoidal waves of different frequencies and amplitudes add up to give a periodic wave of non-sinusoidal form.

Let us consider a periodic signal wave v

*. According to the definition of Fourier series, this periodic signal wave can be written as sum of sinusoidal waves as below.*

Now the question is how can we find the coefficients

I am not going to show you the details of how I obtained the formulas, but you can remember the three general formulas as shown below for obtaining the coefficients. Many of you may not require to find the harmonics by using the formulas below, but those who are interested can use these formulas. Of course, students are required to remember these formulas.

n = 1, 2, 3, 4 .....

Putting the values of n we obtain different coefficients. For example if n=1 we get a1 and b1.

Some knowledge about the properties of the Fourier series will immensely help you. In most cases signal waves maintain symmetry. Depending on the symmetry of the wave we may not be always required to find all the sine and cosine terms coefficients. So now I will guide you through some important properties that you should remember so that just looking at the signal wave you can immediately say which coefficients should be present in the series.

Let us first of all talk a little about harmonics.

What is harmonic ?

Every periodic wave has a Time period(T) which is one complete cycle. The whole signal is the repetition of this period. Frequency (N) of the wave is the number of complete cycles in one second.

clearly N = 1 / T

Observe the general Fourier series, it has a component (a1 sin wt), this sinusoid has the same frequency as the actual signal wave and it is called the fundamental component. The next component is (a2 sin 2wt), its frequency is twice that of fundamental (or original signal wave), this sinusoid is called second harmonic. So also the third, fourth etc.

As an example if the fundamental wave has a frequency of 60 Hz, then the frequency of second harmonic is 120 (2* 60) Hz, third harmonic 180 Hz, 9th harmonic will be 540 Hz etc. The frequency of nth harmonic is (n.60).

Properties of Fourier Series

We will now consider some important and very useful properties of Fourier series

- In the fourier Series the constant term a0 will not appear if the signal wave average value in one period is zero. (one period is T which is equal to 2PI)

A1 and A2 respectively. Here A1=A2, so the average is zero. The wave has a0 equal to zero. You

can also confirm by using the formula above. But shifting the same wave in vertical direction as

redrawn in Fig-B will automatically introduce a0 in Fourier series.

Yes by integrating using the formula above you will find a0. By shifting I have actually disturbed the

symmetry around horizontal axis and introduced the average value a0. Here in this figure a0 is exactly how

much I shifted the whole wave in vertical direction. This a0 is also called DC component of the signal

wave.

- The Fourier series having sine and cosine terms can be combined.

We know that if, p = a1 sin x +b1 cos x then it can be written in the form

p = r sin (x + phi) phi is the angle displacement from sin x.

Using school trigonometry r & phi are found from a1 and b1

Using school trigonometry r & phi are found from a1 and b1

(Remember that same harmonics are combined in this form. sin x with cos 2x or cos x with sin 2x etc.

are not combined in above form).

are not combined in above form).

- Considering the square wave in the above Fig-A we will get only terms with sine function. There will be no cosine terms because the coefficients a1, a2 etc will be zero. This you can verify from above formula also. The Fourier series is:

(sine waves are symmetric about origin). In Fig-C, I have reproduced the square wave. Here I have

calculated only three terms of the Fourier series ' v ', the fundamental, third harmonic and fifth harmonic.

The blue curve is the sum of these three terms of the Fourier series of the square wave shown. You can

see how just by considering three terms of the Fourier series, the blue curve approximate the square

wave. In Fig-D the sum of Fourier series(in blue) is drawn by calculating more coefficients( 9 ). Observe

how the blue curve approximates the suare wave so that I had to remove the square wave from the figure for clarity. Taking more terms the curve will be even smoother.

- Again consider the square wave. I have now chosen the vertical axis by shifting pi/2 to the right and redrawn in Fig-E. Now applying the above equations for getting the coefficients, we will find that the a0 and the sine term coefficients b1, b2...etc has vanished and only cosine terms are there in the series.

The Fourier series is:

It is very important to compare Figure-C and Figure-E. In both cases the square waves are identical.

Only the vertical axes are chosen differently in each cases. Comparing the individual harmonics and their

sum (blue) in both the figures it is clear that actually choosing the position of vertical axis does not

change the component harmonics but what previously you were getting as sine waves have now

become cosine waves automatically. This is only due to the choice of vertical axis.

Only the vertical axes are chosen differently in each cases. Comparing the individual harmonics and their

sum (blue) in both the figures it is clear that actually choosing the position of vertical axis does not

change the component harmonics but what previously you were getting as sine waves have now

become cosine waves automatically. This is only due to the choice of vertical axis.

Both are sinusoidal waves and both are correct. If some intermediate position of axis is chosen, we will

get both sine and cosine terms. The sine and cosine terms can be combined as above to get only either

get both sine and cosine terms. The sine and cosine terms can be combined as above to get only either

phase shifted sine(or cosine) terms for each harmonic.

So the choice of axis does not change the shape or number of harmonics, only mathematically the series

is different.

So it is important to realize that for a particular shape of signal wave the harmonics are fixed, whether

you want to show them as series of sine terms or cosine terms or both, it does not matter. Of course in

exam you may not be allowed to choose axis.

is different.

So it is important to realize that for a particular shape of signal wave the harmonics are fixed, whether

you want to show them as series of sine terms or cosine terms or both, it does not matter. Of course in

exam you may not be allowed to choose axis.

- If the signal wave has quarter wave symmetry, then the Fourier expansion will contain only odd harmonics like 3rd, 5th etc.. To test quarter wave symmetry look at the signal wave at Fig-A. Draw an imaginary vertical line passing through T/4. For the +ve half wave if one side of this vertical line is mirror image of other side then the wave shows quarter wave symmetry.

Note: A sine wave is symmetric with respect to origin (odd function) and cosine is symmetric with

respect to y-axis (even function). Combination of only sine waves will be symmetric with respect

to origin (odd function) and combination of cosine waves will remain symmetric with respect to

y-axis (even function)

respect to y-axis (even function). Combination of only sine waves will be symmetric with respect

to origin (odd function) and combination of cosine waves will remain symmetric with respect to

y-axis (even function)

## 16 comments:

HI

This article is very informative. can u send the practical application of this fourier analysis in optics and power systems elaborately.

my mail : kumar.jagadeesh3@gmail.com

Regards

Thank you for sharing this information.

It will really helpful to solve my confusion

Process $ Chemical Engineering

Great article.

very nice......

thankyou so much

but still I have not understood why do we need to express periodic function in fourier series?...please explain.

SONSO DEBES HALLAR LAS SERIES DE FOURIER Y LUEGO EL PROGRAMA MATLAB PARA GRAFICARLA POR EJM HALLAR LA SERIE DE F COMPLEJA D L RECTIFICACION DE ONDA COMPLETA Y GRAFICARLA EN MATLAB

SONSO must find the Fourier series and then the program MATLAB to graph EJM FINDING BY SERIES D L F COMPLEX full-wave rectification and plot it in Matlab

PUES NO ESTARAS VISIBLE SI NO TE APRUEBO JA JA JAAAAAAAAAAAAAAAAAAAA

You have expressed difficult concepts in a very lucid way.

Your blog awesome, you had shared valuable information about Harmonic distortions are one of the most common and irritating problems in industrial environment. We need to identify the source of harmonics and suppress them for a quality supply of power. Please visit Harmonic Analysis

I like your blog, you shared valuable information about in Harmonic distortions are one of the most common and irritating problems in industrial environment. We need to identify the source of harmonics and suppress them for a quality supply of power. Please visit Harmonic Analysis

I like your blog, you shared valuable information about in #Fourier Series in Electrical Engineering. Harmonic distortions are one of the most common and irritating problems in industrial environment. We need to identify the source of harmonics and suppress them for a quality supply of power. Please visit Harmonic Analysis

Great Blog, Thanks for share this blog. In this blog lot of information is available related to Harmonic Analysis. For some more information please visit our site once power system harmonic analysis .

Nice blog, Thanks for sharing nice information. We Providing Harmonic Analysis Services, power system harmonic analysis. for more Information visit us Harmonic Analysis Services

Thanks for sharing. Our engineers exports on Power System Harmonic Analysis along with complete report on distribution from source to the load feeders to prevent from accidents. power system harmonic analysis

Mast hai yeh toh

## Post a Comment